1992 Ralt RT24 F3000

One of two constructed by Ralt

Sold

(Owner reported history and information)

Marque: 1992 Ralt RT24 Engine(s): Cosworth DFV 3.0L 475 hp
Class: Formula 3000 Judd BV 3.0L 480hp
Chassis#: 027RT-24 973 (teal) Mugen MF308 3.0L 490hp

History

There were only 2 Ralt RT24 F3000 cars produced. This is one of them.

The RT24’s were produced for the 1992 racing season, and were based on the prior Ralt RT23 using the monocoque, gearbox and suspension from the RT23. March Group (March racing cars) purchased Ralt from Ron Tauranac in 1988, so the subsequent Ralts had March chassis tags, even though the cars were still built by the Ralt division.

The RT24’s had revised aero packages that included nose with wing, floor, side pods, engine cover, diffuser and roll bar. These updates were designed by Simtek Engineering, founded by Nick Wirth and Max Mosely, who would be racing their own Simtek F1 car the following season.

According to Ron Tauranac’s biography, ‘Brabham, Ralt, Honda’ (page 183) both of the RT24s were bought in early ’92 by former F1 World Champion Nelson Piquet for Olivier Beretta’s F3000 championship effort. However, both RT24s were sold 2-3 months later when Ralt opted to pull out of F3000. It was decided that further development of the car would be difficult without factory support.

Chassis #973 was purchased from Piquet by Team LeMans, in Japan, for Takao Wada to race in the 1992 Formula Nippon Championship with Nisseki sponsorship. Team LeMans was, and is, a highly successful racing team, and has run drivers such as Michael Schumacher, Johnny Hebert and many others.

Wada raced the Nisseki car in the 1992 Formula Nippon Championship with Mugen power. He later changed to Reynard to complete the season. At that time #973 was converted to Judd power and used for testing only.

Thereafter the Nisseki car was sold. It was next tested in 1998, and then sold to Charlie Warner of Fatto Gatto Racing in the U.S. Warner raced the Nisseki car twice in the US BOSS Series in 2001-2, with a best finish of 5th.

In 2002, Pendragon acquired the Wada/Nisseki car from Fatto Gatto Racing. The Nisseki car was in running condition. The sale also included some body molds.

Today the Nisseki car is offered in complete operating condition, less its bodywork which was stolen from the race car trailer.  The details of the Nisseki car’s restoration are listed below.

Description: 1992 Ralt RT24 #027RT-24 973 (teal)

  • New Kevlar / Carbon Fiber floor
  • Crack checked suspension
  • New Kephos coating on all suspension
  • All new AMB rod ends
  • All new AN hardware
  • Uprights have new wheel bearings
  • Rebuilt Braking system
    • Rebuilt AP brake calipers
    • Some new pistons
    • All new rubber seals
    • All new bleeder nipples
    • All new Aeroquip brake lines with Raychem coating
    • Rebuilt AP master cylinders
  • Rebuilt Hewland gearbox
    • Longitudinal mounted box
    • Uses FT200 gears and dog rings
    • New chromate on all magnesium parts
    • Fresh diff with new friction plates
    • Rejigged all forks and the bearing carrier
    • Rebuilt gearbox oil pump
    • New gearbox oil filter and oil lines
    • All new gearbox hardware – studs, nuts, washers
    • New side plate bearings
    • Rebuilt shift linkage with fresh Apex joints and saddle washers
  • Engine
    • Judd BV.  About 500 miles on the engine.  They were required to last 5000KM.  The previous owner used a 9,000 rpm rev limiter.
    • The car was last run in the fall of 2020.  The engine is turned over monthly.
  • Original (perfect) factory chassis wiring harness
  • Rebuilt nose box
  • Fresh rear wing carbon fiber side plates
  • The Ralt comes with aero balance sheets, wiring diagrams, and a gearbox manual (basically a Hewland FT200 internals in a larger, stronger, case).
  • Fits driver 6’1” 205 LBS

Spares

  • Front uprights
  • Chassis mounts for all front suspension
  • Chassis mounts for all rear suspension
  • 20 sets of gears
  • 4 sets of wheels (1 with rains)
  • Many small parts
  • 2 sets of wheels
  • Gearbox rear bearing carrier
  • Gearbox selector finger housing
  • Gearbox rear cover with pump
  • Brake rotors and hots
  • Brake rotor bobbins
  • Brake pads
  • Set of new Judd BV valve springs

Support parts

  • Nose mold
  • Front wing molds
  • Floor mold
  • Side pod mold
  • Front Lower A-arm Jig
  • Front upper A-arm jig
  • Rear upper and lower A-arm, jig
  • All set up sheets

To see more information, and photos of the Ralt RT24 cars from a prior sale, please go to Ralt RT24 prior sale.

Questions, Comments, Offers?

Please Contact Us if you have any questions or comments, 

or would like to make a non-binding offer.